TYPES OF PAINT REMOVED: Back To Nature IX can remove most varieties of paints & varnishes which are oil or water-based including latex, alkyds, lead, stains, enamels, lacquers and clear paints. Unlike other paint removers, Back To Nature IX can remove more difficult coatings such as two part epoxy, and urethanes.
SURFACES: BTN IX works on a multitude of surfaces including wood, metal, brick, plaster, masonry, stone, concrete, and fiberglass... The paste will not damage any substrate it is applied to. BTN IX is not to be used on sheetrock, plastic, rubber or linoleum surfaces.

INSTRUCTIONS:
A. Preparation - Mask any areas not being stripped with plastic and masking tape.

B. Application
Test Patch - Since it is often hard to know the type or the amount of paint on a surface, small test areas should be stripped to determine the proper application and dwell time needed for paint removal to occur.

1. Apply to a dry surface. If surface is wet or damp, wipe down with a dry cloth. (Note: Applying the stripper to a wet or damp surface may cause a seal to prematurely form between the painted surface and the remover and prevent paint stripping activity, rather than a top seal properly forming between the remover and the environment.)

2. Apply BTN IX approx. 1/32" thick (30 mils) to the surface. Use a brush, roller, trowel, putty knife or hopper type sprayer. Use a wet mil gauge to measure thickness.

3. Spraying - BTN IX can be spray applied using a Hopper gun or 2L3 or larger rotor/stator pump. Drill mix before spraying - System must be flushed with MEK, Acetone, or Denatured Alcohol ONLY before and after application. Use of water or any other solvent to flush, will cause BTN IX to improperly set-up and prevent proper application. - Use NEW material hose.

4. Test Patch - Since it is often hard to know the type or the amount of paint on a surface, a small test area should be stripped to determine the dwell time for removal.
We suggest the patch should be checked for dwell time as follows (only a portion at any one time): Check the patch first at 2 - 4 hours, then periodically thereafter. As a rule of thumb, the greater the layers of paint, the longer the product should be left on. The stripper will usually remove 8-12 layers of paint in 24 hours. More layers of paint (20+) may take longer (2-3+ days). Due to the nature of certain paints such as two part epoxy and urethanes, Back To Nature IX may need more time to be effective. Average dwell time for these coatings may be 48 to 72 hours.

5. Back To Nature IX will easily cling to vertical surfaces and will not wash off even in a driving rain.

6. Clean-up - No Neutralization required. Clean-up with water.

7. For best results apply Back To Nature IX at temperatures between 60 ºF and 80 ºF. Product activity is reduced below a temperature of 60 ºF and may require additional dwell time before all layers of paint are removed.

8. If product freezes in bucket, let thaw and stir vigorously until product is consistent.

9. Coverage for Back To Nature IX varies between 50 and 70 sq. ft. per gal. depending upon the type and amount of paint on a surface.

C. Suggested Removal Techniques
1. Plaster Surfaces
(i) Flat Plaster Surfaces - Easiest removal is achieved using a 4" or wider razor blade scraper (commonly known as a wallpaper stripper) to lift the remover/paint off the surface.

(ii) Decorative Plaster (or Wood) - Use a Back To Nature Stainless Steel Scraper with 5 function detail blade to lift the remover/paint off the surface. Use a stiff bristle brush with Ready-Strip Wash Paint Remover Wash or light amounts of water to remove any residue.

2. Fiberglass Surfaces – Use a putty knife to lift the remover/paint from the surface. Use a stiff bristle brush with Ready-Strip Wash or light amounts of water to remove any residue remaining.

3. Wood
(i) Flat Wood Surfaces - Easiest removal is achieved using a Back To Nature Stainless Steel Scraper to strip remover/paint from the surface. Use a stiff bristle brush with Ready-Strip Wash or light amounts of water to remove any residue remaining.

(ii) Decorative Wood - (see Decorative Plaster)

4. Masonry, Concrete Surfaces - Remove bulk of remover/paint with a stiff putty knife or wire brush. Use a wire brush with Ready-Strip Wash or light amounts of water to remove any residue remaining. Residue can also be removed with a high pressure washer where permitted.

5. Metal Surfaces - Agitate or rough up remover/paint on the surface with a wire brush without attempting removal. This helps to lift bottom layers from the surface. Use a 4" or wider razor blade scraper (wallpaper stripper) or stiff putty knife (pipe railings or irregular surfaces should use the putty knife) to lift remover/paint off the surface. Use a wire brush with Ready-Strip Wash or light amounts of water to remove any residue remaining.

6. Note: Any paint residue remaining on a surface should be removed within a short period of time so that paint residue will not dry up and re-adhere. In some circumstances, it may look like the last layer of paint is still on the surface. This is not a dried layer of paint, but paint & stripper which has been emulsified so that it can be removed as described. Do not mist with water before removal.


SAFETY INSTRUCTIONS: Safety goggles are recommended for eye protection. Protective gloves such as butyl rubber, neoprene gloves are also recommended . Maintain adequate ventilation especially in confined areas. If spraying or misting is expected use NIOSH approved chemical cartridge (organic vapor) respiratory equipment (full face respirator recommended). In case of inhalation - remove victim to fresh air and provide oxygen if breathing is difficult. In case of eye contact - flush exposed areas with large quantities of water. In case of skin contact - wash skin with soap and water. Use emollient skin creams. In case of ingestion - do not induce vomiting. Call physician immediately.